Skip to main content
Versa Networks

Installation Guidelines

  1. Last updated
  2. Save as PDF

This article provides general safety standards and warnings related to installing or connecting a Cloud Services Gateway (CSG) 5000 series appliance.

General Safety Guidelines for CSG5000 Series Appliances

Caution: Before installing or removing a CSG5000 series appliance, ensure that the appliance chassis is electrically connected to ground. When you are installing or removing an appliance, ensure that you wear an electrostatic discharge (ESD) grounding wrist strap. To put the ESD grounding strap on properly, attach it to an ESD point, and then place the other end of the strap around your bare wrist, making good skin contact. Failure to use an ESD grounding strap could damage the appliance.

  • Install the CSG5000 series appliance in compliance with the following local, national, and international electrical codes:
    • United States—National Fire Protection Association (NFPA 70), United States National Electrical Code.
    • Canada—Canadian Electrical Code, Part 1, CSA C22.1.
    • Other countries—International Electromechanical Commission (IEC) 60364, Part 1 through Part 7. Evaluated to the TN power system.
  • Locate the emergency power-off switch in the installation area. In case of an electrical accident, turn off the power quickly.
  • Disconnect power to the appliance before installing or removing it.
  • Disconnect power from the circuit that is being used for the appliance.
  • If hazardous conditions exist, do not work alone.
  • If you are working under conditions that might be hazardous to the eyes, wear safety glasses or goggles.

General Safety Guidelines for CSG5200 and CSG5250 Models

  • This equipment is to be installed for operation in an environment with maximum ambient temperature below 40°C.
  • The machine can only be used in a restricted access location and must be installed by a skilled person.
  • ESD can damage equipment and impair electrical circuitry. ESD damage occurs when electronic components are improperly handled and can result in complete or intermittent failures. Be sure to follow ESD-prevention procedures when removing and replacing components to avoid these problems.
  • Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is available, ground yourself by touching the metal part of the chassis.

Français:

  • Les matériels sont destinés à être installés dans des EMPLACEMENTS À ACCÈS RESTREINT.
  • Les décharges électrostatiques (ESD) peuvent endommager l’équipement et gêner les circuits électriques. Des dégâts d’ESD surviennent lorsque des composants électroniques sont mal manipulés et peuvent causer des pannes totales ou intermittentes. Suivez les procédures de prévention d’ESD lors du retrait et du remplacement de composants.
  • Portez un bracelet anti-ESD et veillez à ce qu’il soit bien au contact de la peau. Si aucun bracelet n’est disponible, reliez votre corps à la terre en touchant la partie métallique du châssis.

Battery Cautions and Warnings

  • There is risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
  • There is danger of explosion if the battery is mishandled or incorretly replaced. Replace only with the same type of battery. Do not disassemble it or attempt to recharge it outside the system. Do not crush, puncture, dispose of in fire, short the external contacts, or expose to water or other liquids. Dispose of the battery in accordance with local regulations and instructions from your service provider.
  • Lithium battery caution: There is danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of batteries according to the manufacturer's instructions.
  • Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
  • Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

Français:

  • Risque d’explosion si la batterie est remplacée par un type incorrect. Mettre au rebus les batteries usagées selon les instructions.
  • Pile au lithium Attention: Risque d'explosion si la pile n'est pas remplacée correctement. Remplacez uniquement par un type identique ou équivalent. Jetez les piles conformément aux instructions du fabricant.
  • Mise au rebut d'une BATTERIE dans un feu ou un four chaud, ou écrasement ou découpage mécanique d'une BATTERIE, pouvant entraîner une EXPLOSION
  • Laisser une BATTERIE dans un environnement extrêmement chaud pouvant entraîner une EXPLOSION ou une fuite de liquide ou de gaz inflammable
  • UNE BATTERIE soumise à une pression d'air extrêmement basse pouvant entraîner une EXPLOSION ou une fuite de liquide ou de gaz inflammable.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement

This equipment complies with CE and FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Warning: Operation of this equipment in a residential environment could cause radio interference.

Warning: Operation of this equipment is for indoor use only.

  1. Back to top
  • Was this article helpful?

Recommended articles

  1. Page type
    Topic
  2. Tags
    This page has no tags.